F.O.B. DESTINATION (STATEWIDE CONTRACT)

F.O.B. DESTINATION FOR SHIPMENT TO:

ALL STATE AGENCIES, LOCAL GOVERNMENT AGENCIES AND AUTHORIZED
NON-PROFIT ENTERPRISES LOCATED WITHIN THE STATE OF TENNESSEE.

TERM OF CONTRACT

THE ANTICIPATED EFFECTIVE DATE AND EXPIRATION DATE OF THE CONTRACT ARE
SHOWN ON THE FRONT OF THIS SOLICITATION. IF AWARD HAS NOT BEEN MADE BY
THE ANTICIPATED EFFECTIVE DATE, THEN THE CONTRACT SHALL BECOME
EFFECTIVE UPON THE DATE THE BID IS ACCEPTED AND CONTRACT AWARDED BY
THE STATE, AS INDICATED BY THE PURCHASING AGENT'S SIGNATURE ON THE
CONTRACT NOTICE OF AWARD (NOTE: THE CHANGE OF EFFECTIVE DATE MAY NOT
RESULT IN A CHANGE OF THE ANTICIPATED EXPIRATION DATE.)

RENEWAL OPTIONS: THIS CONTRACT MAY BE RENEWED UPON SATISFACTORY
COMPLETION OF THE INITIAL CONTRACT TERM. THE STATE RESERVES THE RIGHT
TO EXECUTE UP TO 1 OPTION TO RENEW THIS CONTRACT ANNUALLY UNDER THE
SAME TERMS AND CONDITIONS FOR A PERIOD NOT TO EXCEED 12 MONTHS EACH BY
THE STATE. IT IS MUTUALLY UNDERSTOOD AND AGREED THAT THE STATE'S
COMMITMENT IS LIMITED TO A BASE TERM CONTRACT, NOT TO EXCEED TWELVE
(12) MONTHS, WHICH IS SUBJECT TO RENEWAL ANNUALLY AT THE STATE'S SOLE
OPTION.

IT IS UNDERSTOOD AND AGREED THAT THE STATE RESERVES THE RIGHT TO
EXTEND THE TERM CONTRACT PERIOD RESULTING FROM THIS SOLICITATION AN
ADDITIONAL PERIOD OF TIME, NOT TO EXCEED 180 DAYS BEYOND THE NORMAL
EXPIRATION DATE OF SUCH CONTRACT, UPON MUTUAL WRITTEN AGREEMENT BY
BOTH PARTIES, UNDER THE SAME TERMS AND CONDITIONS. PROVIDED, HOWEVER,
IN NO EVENT SHALL THE MAXIMUM TERM OF A CONTRACT EXCEED A TOTAL OF
SIXTY (60) MONTHS.
DELIVERY TIME (DAYS)

ALL ITEMS MUST BE DELIVERED WITHIN APPROXIMATELY TWENTY-ONE (21) DAYS
AFTER RECEIPT OF PURCHASE ORDER.

FREIGHT F.O.B. STATE AND LOCAL GOVERNMENT AGENCIES

ALL QUOTATIONS SHALL BE F.O.B. DESTINATION. THE TERM F.O.B.
DESTINATION SHALL MEAN DELIVERED AND UNLOADED ONTO THE RECEIVING DOCK
OF ANY STATE AGENCY AND, WHEN APPLICABLE, ANY LOCAL GOVERNMENT AGENCY
OR AUTHORIZED CORPORATION WITHIN THE STATE OF TENNESSEE, WITH ALL
CHARGES FOR TRANSPORTATION AND UNLOADING PREPAID BY THE
VENDOR/CONTRACTOR.

FIRM BID PRICE PERIOD (PRICE INCREASE ALLOWED AFTER TIMEFRAME)

PRICES QUOTED SHALL BE FIRM FOR 365 DAYS FOLLOWING THE DATE
OF THE AWARD, EXCEPT THE STATE SHALL BE ADVISED OF, AND RECEIVE THE
BENEFIT OF, ANY PRICE DECREASE IN EXCESS OF FIVE (5) PERCENT
AUTOMATICALLY. THE VENDOR/CONTRACTOR MUST PROVIDE WRITTEN PRICE
REDUCTION INFORMATION WITHIN TEN (10) DAYS OF ITS EFFECTIVE DATE.

INSPECTION

ALL MATERIALS, EQUIPMENT, AND SUPPLIES ARE SUBJECT TO INSPECTION AND
TESTING. ITEMS THAT DO NOT MEET SPECIFICATIONS WILL BE REJECTED.
FAILURE TO REJECT UPON RECEIPT DOES NOT RELIEVE THE CONTRACTOR OF
LIABILITY. WHEN SUBSEQUENT TESTS AFTER RECEIPT ARE CONDUCTED AND
WHEN SUCH TESTS REVEAL DAMAGE OR FAILURE TO MEET SPECIFICATIONS, THE
STATE MAY SEEK DAMAGES REGARDLESS OF WHETHER A PART OR ALL OF THE
MERCHANDISE HAS BEEN CONSUMED.

WARRANTY PERIOD

A BIDDER WARRANTS THE PRODUCT TO BE FREE OF DEFECTS FOR

______________________________.

PURCHASE ORDER RELEASE (SWC)

ORDERS FOR SERVICES OR SUPPLIES THAT ARE INCLUDED ON STATEWIDE
CONTRACTS SHALL BE PREPARED BY AGENCIES ON DEPARTMENTAL PURCHASE
ORDERS AND FORWARDED DIRECTLY TO THE VENDOR/CONTRACTOR. THESE PURCHASE
ORDERS, WHEN RECEIVED BY THE VENDOR/CONTRACTOR, SERVE AS AUTHORIZATION
FOR SHIPMENT. ITEMS FROM DIFFERENT CONTRACTS MAY BE COMBINED ON A
SINGLE PURCHASE ORDER TO THE SAME VENDOR/CONTRACTOR TO MEET MINIMUM
ORDER REQUIREMENTS. LOCAL GOVERNMENT AGENCIES OR AUTHORIZED
CORPORATIONS, WHERE APPLICABLE, WILL ISSUE THEIR PURCHASE ORDER
RELEASES DIRECTLY TO THE VENDOR/CONTRACTOR(S).

BILLING INSTRUCTIONS
THE CONTRACTOR SHALL INVOICE THE STATE ONLY AFTER COMPLETION OF THE
WORK DESCRIBED IN THE PURCHASE ORDER/CONTRACT, AND AS REQUIRED BELOW
PRIOR TO ANY PAYMENT.

THE CONTRACTOR SHALL SUBMIT AN INVOICE, WITH ALL NECESSARY SUPPORTING
DOCUMENTATION, TO: STATE AGENCY BILLING ADDRESS

SUCH INVOICE SHALL CLEARLY AND ACCURATELY DETAIL THE FOLLOWING
REQUIRED INFORMATION.

INVOICE/REFERENCE NUMBER; (ASSIGNED BY THE CONTRACTOR)
INVOICE DATE;
CONTRACT AND/OR PURCHASE ORDER NUMBER; (ASSIGNED BY THE STATE)
ACCOUNT NAME; PROCURING STATE AGENCY AND DIVISION NAME
ACCOUNT/CUSTOMER NUMBER; (UNIQUELY ASSIGNED BY THE CONTRACTOR TO
THE ABOVE-REFERENCED ACCOUNT NAME;
CONTRACTOR NAME;
CONTRACTOR FEDERAL EMPLOYER IDENTIFICATION NUMBER OR SOCIAL
SECURITY NUMBER; (AS REFERENCED IN CONTRACT)
CONTRACTOR CONTACT (NAME, PHONE, AND/OR FAX FOR THE INDIVIDUAL TO
CONTACT WITH BILLING QUESTIONS);
CONTRACTOR REMITTANCE ADDRESS;
DESCRIPTION OF DELIVERED ITEM OR SERVICE; AND
TOTAL AMOUNT DUE FOR DELIVERED ITEM OR SERVICE.

THE CONTRACTOR UNDERSTANDS AND AGREES THAT THE INVOICE SHALL;

INCLUDE ONLY CHARGES FOR SERVICE DESCRIBED IN CONTRACT OR PURCHASE
ORDER AND IN ACCORDANCE WITH PAYMENT TERMS AND CONDITIONS SET FORTH
IN CONTRACT OR PURCHASE ORDER;

NOT INCLUDE ANY FUTURE WORK BUT WILL ONLY BE SUBMITTED FOR
COMPLETED SERVICE; AND

NOT INCLUDE SALES TAX OR SHIPPING CHARGES (UNLESS OTHERWISE
STIPULATED IN THE CONTRACT OR PURCHASE ORDER).

THE CONTRACTOR AGREES THAT TIMEFRAME FOR PAYMENT (AND ANY DISCOUNTS)
BEGINS WHEN THE STATE IS IN RECEIPT OF A CORRECT INVOICE MEETING THE
MINIMUM REQUIREMENTS ABOVE.

PAYMENT

IT SHALL BE THE RESPONSIBILITY OF THE "BILL TO" AGENCY TO MAKE
PAYMENT. ANY QUESTIONS CONCERNING PAYMENT SHOULD BE ADDRESSED TO THE
"BILL TO" AGENCY LISTED IN THE TOP, RIGHT SIDE OF THE PURCHASE ORDER,
NOT THE PURCHASING DIVISION.

VENDOR CONTRACT ADMINISTRATOR (LISTING)

BUSINESS CONTACT - PERSON WHO CAN SERVE AS PROJECT MANAGER FOR THIS
CONTRACT

NAME:_____________________________________________


TITLE:____________________________________________


ADDRESS:__________________________________________

__________________________________________


PHONE:(A/C) _______ NUMBER __________________

FAX: (A/C) _______ NUMBER __________________

E-MAIL ADDRESS: _____________________________

TECHNICAL CONTACT (IF DIFFERENT FROM ABOVE) - PERSON WITHIN YOUR
ORGANIZATION WHO CAN ASSIST WITH THE CREATION OF AN ELECTRONIC
PRODUCT CATALOG FOR YOUR CONTRACT LINE ITEMS


NAME:_____________________________________________


TITLE:____________________________________________


ADDRESS:__________________________________________

__________________________________________


PHONE:(A/C) _______ NUMBER __________________

FAX: (A/C) _______ NUMBER __________________

E-MAIL ADDRESS: _____________________________

CORPORATE E-COMMERCE CONTACT - (IF DIFFERENT FROM ABOVE) PERSON WITHIN
YOUR ORGANIZATION WHO BEST UNDERSTANDS THE COMPANY E-COMMERCE
INITIATIVES AND WILL COMMUNICATE THESE INITIATIVES TO THE ORGANIZATION

NAME:_____________________________________________


TITLE:____________________________________________


ADDRESS:__________________________________________

__________________________________________


PHONE:(A/C) _______ NUMBER __________________

FAX: (A/C) _______ NUMBER __________________

E-MAIL ADDRESS: _____________________________
SPECIFICATIONS GOVERN OVER BRAND NAMES LISTED

THE ACCEPTABLE BRANDS AND MODEL NUMBERS ARE BELIEVED TO MEET ALL
WRITTEN SPECIFICATIONS. HOWEVER, IF AN ERROR EXISTS, THE
DEFINITIVE SPECIFICATIONS WILL GOVERN.

SUBCONTRACTING: RESPONSIBILITIES AND LIABILITIES

THE CONTRACTOR SHALL NOT ENTER INTO ANY SUBCONTRACT FOR SERVICES
WITHOUT THE WRITTEN CONSENT OF THE DEPUTY COMMISSIONER, DEPARTMENT OF
GENERAL SERVICES, PURCHASING DIVISION. THE AWARDED CONTRACTOR IS
RESPONSIBLE FOR WORK, SERVICE, PERFORMANCE, CONTRACTUAL LIABILITY
WORKERS' COMPENSATION INJURIES OF EMPLOYEES AND SUBS (UNLESS
SUBCONTRACTOR ASSUMES RESPONSIBILITY AND FURNISHES AN ORIGINAL
CERTIFICATE OF INSURANCE AS PROOF OF INSURANCE FOR WORKERS'
COMPENSATION AND NAMING THE STATE OF TENNESSEE AS ADDITIONALLY INSURED
FOR GENERAL LIABILITY), AND PAYMENT TO THE SUBCONTRACTOR. ALL COSTS
INCURRED FOR SUBCONTRACTING MUST BE INCLUDED IN THE BID PRICE.

THE SUCCESSFUL BIDDER(S) WILL BE REQUIRED TO FURNISH A LABOR AND
MATERIAL SURETY BOND ISSUED BY A SURETY COMPANY LICENSED TO DO
BUSINESS IN THE STATE OF TENNESSEE IN THE AMOUNT OF TWENTY-FIVE (25) %
OF THE TOTAL CONTRACT AMOUNT. SUCH BOND SHALL BE FURNISHED TO THE
PURCHASING DIVISION WITHIN TEN (10) WORKING DAYS AFTER THE REQUEST.
THE SURETY BOND WILL INSURE THAT THE CONTRACTOR WILL PAY FOR ALL LABOR
AND MATERIALS USED BY THE CONTRACTOR, OR ANY IMMEDIATE OR REMOTE
SUBCONTRACTOR UNDER THE CONTRACTOR, IN SUCH CONTRACT, IN LAWFUL MONEY
OF THE UNITED STATES.


LIST BELOW THE NAME, COMPLETE ADDRESS AND PHONE NUMBER OF ALL
SUBCONTRACTOR(S):

______________________________________________________________________

______________________________________________________________________

______________________________________________________________________

OUTBOARD MOTORS FOR STATEWIDE CONTRACT

A. ALL MOTORS ON THIS BID ARE TO BE COMPLETE AND READY FOR OPERATION
WHEN DELIVERED TO THE AGENCY - EXCEPT WHERE NOTED OTHERWISE

B. UNIT PRICE IS TO INCLUDE ALL REMOTE CONTROLS AND NECESSARY CABLES.
ORDERING AGENCIES WILL BE ADVISED TO DESIGNATE REMOTE CABLE LENGTHS
AND/OR PROPELLER PITCH, ON THEIR PURCHASE ORDERS.

MOTOR SPECIFICATIONS ARE LISTED BELOW:


LINE 1, 135.0 H.P.

1. HORSEPOWER - PROP 135.0
2. ENGINE TYPE 4 CYLINDER
3. DISPLACEMENT 121 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R, SIDE MOUNTED
7. THROTTLE REMOTE, SIDE MOUNTED
8. TILT/TRIM POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 420 LBS. MAXIMUM
12. KILL SWITCH MANUFACTURER STANDARD
13. TILT/TRIM INDICATOR DASH MOUNTED

ACCEPTABLE BRANDS AND MODELS:
MERCURY 135L OPTIMAX
JOHNSON J135PLSI
OR EQUAL


LINE 2, 150.0 H.P. OUTBOARD MOTOR (20 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 150.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 4500 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 450 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP.
14. KILL SWITCH MANUFACTURER STANDARD.
15. DIGITAL MULTI GAUGE SYSTEM THAT INDICATES RPM, ENGINE TEMPERATURE,
ENGINE HOURS,TRIM GUAGE, FUEL FLOW AND WATER PRESSURE (SMARTCRAFT,
I/COMMAND OR EQUAL).
16. TO INCLUDE ALL HARDWARE NECESARY TO INSTALL ENGINE
17. TO MEET 2009 EPA STANDARDS
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E150DSL
MERCURY 150L OPTIMAX
OR EQUAL


LINE 3, 150.0 H.P. OUTBOARD MOTOR (25 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 150.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 4500 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 450 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP
14. KILL SWITCH MANUFACTURER STANDARD
15. DIGITAL MULTI GAUGE SYSTEM THAT INDICATES RPM, ENGINE TEMPERATURE,
ENGINE HOURS, TRIM GUAGE, FUEL FLOW AND WATER PRESSURE(I/COMMAND,
SMARTCRAFT OR EQUAL).
16. TO INCLUDE ALL HARDWARE NECESSARY TO INSTALL ENGINE.
17. TO MEET 2009 EPA STANDARDS.
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E150DPX
MERCURY 150XL OPTIMAX
OR EQUAL


LINE 4, 175.O H.P. OUTBOARD MOTOR (20 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 175.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 450 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP
14. KILL SWITCH MANUFACTURER STANDARD
15. DIGITAL MULTI GAUGE SYSTEM THAT INDICATES RPM, ENGINE TEMPERATURE,
ENGINE HOURS, TRIM GAUGE, FUEL FLOW AND WATER PRESSURE (I/COMMAND,
SMARTCRAFT OR EQUAL).
16. TO INCLUDE ALL HARDWARE NECESSARY TO INSTALL ENGINE.
17. TO MEET 2009 EPA STANDARDS.
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E175DSL
MERCURY 175L OPTIMAX
OR EQUAL


LINE 5, 200.0 H.P. OUTBOARD MOTOR (20 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 200.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 175 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 530 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP
14. KILL SWITCH MANUFACTURER STANDARD
15. DIGITAL MULTI GAUGE SYSTEM THAT INDICATE RPM, ENGINE TEMPERATURE,
ENGINE HOURS, TRIM GAUGE, FUEL FLOW AND WATER PRESSURE (I/COMMAND,
SMARTCRAFT OR EQUAL).
16. TO INCLUDE ALL HARDWARE NECESSARY TO INSTALL ENGINE.

17. TO MEET 2009 EPA STANDARDS
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E200DSL
MERCURY 200L OPTIMAX
OR EQUAL

LINE 6, 225.0 H.P. OUTBOARD MOTOR (25 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 225.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 175 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 530 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP
14. KILL SWITCH MANUFACTURER STANDARD
15. DIGITAL MULTI GAUGE SYSTEM THA INDICATE RPM, ENGINE TEMPERATURE,
ENGINE HOURS, TRIM GAUGE, FUEL FLOW AND WATER PRESSURE (I/COMMAND,
SMARTCRAFT OR EQUAL).
16. TO INCLUDE ALL HARDWARE NECESSARY TO INSTALL ENGINE.
17. TO MEET 2009 EPA STANDARDS.
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E225DPX
MERCURY 225XL OPTIMAX
OR EQUAL


LINE 7, 25.0 H.P.

1. HORSEPOWER - PROP 25.0
2. ENGINE TYPE 2 CYLINDER, FOUR STROKE
3. DISPLACEMENT 30.4 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM MANUAL
6. GEAR SHIFT TILLER OR MOTOR MOUNTED, F-N-R
7. THROTTLE TWIST GRIP
8. SHAFT LENGTH 15 INCHES
9. PROPELLER STAINLESS STEEL
10. WEIGHT 136 LBS.
11. KILL SWITCH MANUFACTURER STANDARD
12. TO INCLUDE OIL INJECTION SYSTEM

ACCEPTABLE BRANDS AND MODELS
HONDA B25
MERCURY 25MS
OR EQUAL

LINE 8, 25.0 H.P.

1. HORSEPOWER - PROP 25.0
2. ENGINE TYPE 2 CYLINDER, FOUR STROKE
3. DISPLACEMENT 30.4 CUBIC INCHES
4. STARTING SYSTEM MANUAL
5. GEAR SHIFT TILLER OR MOTOR MOUNTED, F-N-R
6. THROTTLE TWIST GRIP
7. SHAFT LENGTH 20 INCHES
8. PROPELLER STAINLESS STEEL
9. WEIGHT 136 LBS.
10. KILL SWITCH MANUFACTURER STANDARD


ACCEPTABLE BRANDS AND MODELS:
HONDA B25
MERCURY 25ML
OR EQUAL

LINE 9, 25.0 H.P.

1. HORSEPOWER-PROP 25.0
2. ENGINE TYPE 2 CYLINDER, FOUR STROKE
3. DISPLACEMENT 30.4 CUBIC INCHES
4. STARTING SYSTEM ELECTRIC
5. GEAR SHIFT REMOTE, F-N-R, SIDE MOUNTED
6. THROTTLE REMOTE, SIDE MOUNTED
7. TILT MANUAL
8. SHAFT LENGTH 15 INCHES
9. PROPELLER STAINLESS STEEL
10. WEIGHT 136 LBS.
11. KILL SWITCH MANUFACTURER STANDARD
12. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF25
MERCURY 25ES
OR EQUAL

LINE 10, 25.0 H.P.

1. HORESPOWER - PROP 25.0
2. ENGINE TYPE 2 CYLINDER, FOUR STROKE
3. DISPLACEMENT 30.4 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R, SIDE MOUNTED
7. THROTTLE REMOTE, SIDE MOUNTED
8. SHAFT LENGTH 20 INCHES
9. PROPELLER STAINLESS STEEL
10. WEIGHT 136 LBS.
11. KILL SWITCH MANUFACTURER STANDARD
12. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS:
HONDA BF40
MERCURY 25SEL
OR EQUAL

LINE 11, 40.0 H.P.

1. HORSEPOWER - PROP 40.0
2. ENGINE TYPE 3 CYLINDER, FOUR STROKE
3. DISPLACEMENT 45.6 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R, SIDE MOUNTED
7. THROTTLE REMOTE, SIDE MOUNTED
8. TILT MANUAL OR POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 182 LBS.
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF40
MERCURY 40EL
OR EQUAL

LINE 12, 50.0 H.P.

1. HORSEPOWER - PROP 50.0
2. ENGINE TYPE 4 CYLINDER, FOUR STROKE
3. DISPLACEMENT 49.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM MINIMUM
5. STARTING SYSTEM ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE, F-N-R, SIDE MOUNTED
7. THROTTLE REMOTE
8. TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 248 LBS.
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF50
MERCURY 50ELP
OR EQUAL

LINE 13, 75.0 H.P.

1. HORSEPOWER - PROP 75.0
2. ENGINE TYPE 4 CYLINDER, FOUR STROKE
3. DISPLACEMENT 97.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE, F-N-R, SIDE MOUNTED
7. THROTTLE REMOTE
8. TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 370 LBS
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATOIN INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF75
MERCURY 75ELP
OR EQUAL

LINE 14, 115.0 H.P.

1. HORSEPOWER - PROP 115.0
2. ENGINE TYPE 4 CYLINDER, FOUR STROKE
3. DISPLACEMENT 106.2 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE, F-N-R
7. THROTTLE REMOTE
8. TRIM & TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 386 LBS.
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA B115
MERCURY 115ELP
OR EQUAL

LINE 15, 200.0 H.P.

1. HORSEPOWER - PROP 200.0
2. ENGINE TYPE 6 CYLINDER, FOUR STROKE
3. DISPLACEMENT 158.5 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R
7. THROTTLE REMOTE
8. TRIM & TILT POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 583 LBS.
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF200
MERCURY 200XL VERADO
OR EQUAL

LINE 16, 225.0 H.P.

1. HORSEPOWER - PROP 225.0
2. ENGINE TYPE 6 CYLINDER, FOUR STROKE
3. DISPLACEMENT 158.5 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R
7. THROTTLE REMOTE
8. TRIM & TILT POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 583 LBS.
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF225
MERCURY 225XL VERADO
OR EQUAL

LINE 17, 75.0 H.P.

1. HORSEPOWER - PROP 75.0
2. ENGINE TYPE 3 CYLINDER,
3. DISPLACEMENT 185.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC KEYED IGNITION
6. GEAR SHIFT REMOTE, F-N-R
7. THROTTLE REMOTE
8. TRIM & TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 370 LBS.
12. REMOTE CONTRL WITH CABLES
13. TO MEET 2009 EPA STANDARDS


ACCEPTABLE BRANDS AND MODELS
MERCURY 75 ELPTO OPTIMAX
EVENRUDE 75 ETEC
OR EQUAL

LINE 18, 90.0 H.P.

1. HORSEPOWER - PROP 90.0 H.P.
2. ENGINE TYPE 3 CYLINDER
3. DISPLACEMENT 185.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC KEYED IGNITION
6. GEAR SHIFT REMOTE, F-N-R SIDE MOUNTED
7. THROTTLE REMOTE
8. TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 375 LBS.
12. KILL SWITCH MANUFACTURER'S STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS/MODELS
MERCURY 90 ELPTO OPTIMAX
EVENRUDE 90 ETEC
OR EQUAL

LINE 19, 115.0 H.P.

1. HORSEPOWER - PROP 115 H.P.
2. ENGINE TYPE 3 CYLINDER
3. DISPLACEMENT 185 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC KEYED
6. GEAR SHIFT FORWARD, F-N-R SIDE MOUNTED
7. THROTTLE REMOTE
8. TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS
11. WEIGHT 375 LBS
12. REMOTE CONTROL WITH CABLES
13. MOTOR TO BE SUPPLILED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CACLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
MERCURY 115 ELPTO OPTIMAX
EVENRUDE 115 ETEC
OR EQUAL

LINE 20, 150.0 H.P.

1. HORSEPOWER - PROP 150.0 H.P.
2. ENGINE TYPE 4 CYLINDER, FOUR STROKE
3. DISPLACEMENT 105.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R
7. THROTTLE REMOTE
8. TRIM & TILT POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 406 LBS
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLIED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA B150
MERCURY 150L VERADO
YAMAHA F150
OR EQUAL

LINE 21, 150.0 H.P. OUTBOARD MOTOR

1. HORSEPOWER - PROP 150
2. ENGINE TYPE 6 CYLINDER, FOUR STROKE
3. DISPLACEMENT 105.0 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING SYSTEM ELECTRIC
6. GEAR SHIFT REMOTE, F-N-R
7. THROTTLE REMOTE
8. TRIM & TILT POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 406 LBS
12. KILL SWITCH MANUFACTURER STANDARD
13. MOTOR TO BE SUPPLILED COMPLETE AND READY FOR OPERATION INCLUDING
REMOTE CABLES. CABLE LENGTH TO BE DESIGNATED ON PURCHASE ORDER.

ACCEPTABLE BRANDS AND MODELS
HONDA BF 150
MERCURY 150XL VERADO
YAMAHA F150
OR EQUAL

LINE 22, 150.0 H.P. OUTBOARD MOTOR (20 INCH WITHOUT CONTROLS)

1. HORSEPOWER - PROP 150.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 4500 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 450 LBS. MAXIMUM
12. TO MEET 2009 EPA STANDARDS

ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E150DSL
MERCURY 150L OPTIMAX
OR EQUAL


LINE 23, 150.0 H.P. OUTBOARD MOTOR (25 INCH WITHOUT CONTROLS)

1. HORSEPOWER - PROP 150.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 4500 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGHT 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 450 LBS MAXIMUM
12. TO MEET 2009 EPA STANDARDS.

ACCEPTABLE BRANDS AND MODELS
EVINRUDE E150DPX
MERCURY 150XL OPTIMAX
OR EQUAL


LINE 24, 175.0 H.P. OUTBOARD MOTOR (20 INCH WITHOUT CONTROLS)

1. HORSEPOWER - PROP 175.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGHT 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 450 LBS. MAXIMUM
12. TO MEET 2009 EPA STANDARDS.

ACCEPTABLE BRANDS AND MODELS
EVINRUDE E175DSL
MERCURY 175L OPTIMAX
OR EQUAL


LINE 25, 175.0 H.P. OUTBOARD MOTOR (25 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 175.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 450 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP
14. KILL SWITCH MANUFACTURER STANDARD
15. DIGITAL MULTI GAUGE SYSTEM THAT INDICATES RPM, ENGINE TEMPERATURE,
ENGINE HOURS, TRIM GAUGE, FUEL FLOW AND WATER PRESSURE (I/COMMAND,
SMARTCRAFT OR EQUAL).
16. TO INCLUDE ALL HARDWARE NECESSARY TO INSTALL ENGINE
17. TO MEET 2009 EPA STANDARDS.
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E175DPX
MERCURY 175XL OPTIMAX
OR EQUAL


LINE 26, 175.0 H.P. OUTBOARD MOTOR (25 INCH WITHOUT CONTROLS)

1. HORSEPOWER 175.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 150 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 450 LBS. MAXIMUM
12. TO MEET 2009 EPA STANDARDS.

ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E175DPX
MERCURY 175XL OPTIMAX


LINE 27, 200.0 H.P. OUTBOARD MOTOR (20 INCH WITHOUT CONTROLS)

1. HORSEPOWER - PROP 200.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 175 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 20 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 530 LBS. MAXIMUM
12. TO MEET 2009 EPA STANDARDS.

ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E200DSL
MERCURY 200L OPTIMAX
OR EQUAL


LINE 28, 200.0 H.P. OUTBOARD MOTOR (25 INCH WITH CONTROLS)

1. HORSEPOWER - PROP 200.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 175 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITON
6. GEAR SHIFT REMOTE
7. THOTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS(VENGENCE/REBEL SERIES OR EQUAL)
11. WEIGHT 530 LBS. MAXIMUM
12. TO INCLUDE REMOTE CABLE CONTROLS WITH A CENTER STEER BINNACLE
MOUNT CONTROL OR A SIDE MOUNT CONTROL. AGENCY WILL SPECIFY CABLE
LENGTHS AND CONTROL MOUNT TYPE AT TIME OF ORDER.
13. TO INCLUDE REMOTE MOUNTED OIL RESERVOIR/PUMP
14. KILL SWITCH MANUFACTURER STANDARD
15. DIGITAL MULTI GAUGE SYSTEM THAT INDICATES RPM, ENGINE TEMPERATURE,
ENGINE HOURS, TRIM GAUGE, FUEL FLOW AND WATER PRESSURE (I/COMMAND,
SMARTCRAFT OR EQUAL).RE NECESSARY TO INSTALL ENGINE
17. TO INCLUDE ALL HARDWARE NECESSARY TO INSTALL ENGINE.
18. TO MEET 2009 EPA STANDARDS.
ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E200DPX
MERCURY 200XL OPTIMAX
OR EQUAL


LINE 29, 200.0 H.P. OUTBOARD MOTOR (25 INCH WITHOUT CONTROLS)

1. HORSEPOWER - PROP 200.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 175 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 530 LBS. MAXIMUM
12. TO MEET 2009 EPA STANDARDS

ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E200DPX
MERCURY 200XL OPTIMAX
OR EQUAL


LINE 30, 225.0 H.P. OUTBOARD MOTOR (25 INCH WITHOUT CONTROLS)

1. HORSEPOWER - PROP 225.0
2. ENGINE TYPE 6 CYLINDER
3. DISPLACEMENT 175 CUBIC INCHES
4. FULL THROTTLE RANGE 5000 RPM
5. STARTING ELECTRIC, KEYED IGNITION
6. GEAR SHIFT REMOTE
7. THROTTLE REMOTE
8. TILT/TRIM POWER
9. SHAFT LENGTH 25 INCHES
10. PROPELLER STAINLESS STEEL
11. WEIGHT 530 LBS. MAXIMUM
12. TO MEET 2009 EPA STANDARDS.

ACCEPTABLE BRANDS AND MODELS:
EVINRUDE E225DPX
MERCURY 225XL OPTIMAX
OR EQUAL