SUBSEQUENT MODEL YEAR MINIMUM SPECIFICATIONS

ALL SPECIFICATIONS AS LISTED IN THIS INVITATION TO BID ARE TO BE
CONSIDERED AS MINIMUM(S) AND ARE TO BE CONSIDERED MINIMUM(S) FOR ALL
SUBSEQUENT MODEL YEAR(S) VEHICLES PROVIDED AS A PART OF ANY CONTRACT
RESULTING FROM THIS INVITATION TO BID; UNLESS, IN THE EVENT A
PARTICULAR SPECIFICATION(S) REQUIREMENT IS NO LONGER MADE AVAILABLE BY
THE VEHICLE MANUFACTURER, WHEREIN THE STATE RESERVES THE SOLE RIGHT TO
CONSIDER THE CHANGE MINOR AND CONTINUE THE CONTRACT FOR THAT SUBSQUENT
MODEL YEAR. THE PURCHASING DIVISION MUST BE NOTIFIED OF AND APPROVE
OF ANY/ALL MINIMUM SPECIFICATION DEVIATIONS PRIOR TO SUBSEQUENT MODEL
YEAR CONTRACT CHANGES.

THE SUCCESSFUL VENDOR MUST ADVISE THE PURCHASING DIVISION IN WRITING
OF THE DATE UPON WHICH A SUBSEQUENT MODEL YEAR VEHICLE WILL BE
APPLICABLE FOR THE PURPOSE OF PURCHSE ORDER ISSUANCE. ALL PURCHASE
ORDERS ISSUED AFTER THAT DATE ARE TO REFLECT THAT SUBSEQUENT MODEL
YEAR. UNDER NO EVENT SHALL ANY PURCHASE ORDER BE ACCEPTED BY OR
VEHICLE BE DELIVERED BY THE SUCCESSFUL VENDOR UNTIL SUCH APPROVAL HAS
BEEN SO GRANTED BY THE PURCHASING DIVISION.

2010 MODEL YEAR

ALL VEHICLES BID SHALL BE 2010 MODEL YEAR.
SUBSTITUTION OF SUBSEQUENT MODEL YEAR VEHICLE

SUBSEQUENT MODEL YEAR ACCEPTANCE SHALL BE AN OPTION AT THE STATE'S
DISCRETION AND SHALL REMAIN VALID EXCEPT UPON THE WRITTEN NOTIFICATION
FROM THE VEHICLE MANUFACTURER THAT (1) AWARD VEHICLE MODEL IS NO
LONGER BEING PRODUCED AND THEREFORE NOT AVAILABLE FROM THE
MANUFACTURER; (2) THERE IS NOT A NEW MODEL YEAR REPLACEMENT FOR THE
AWARD VEHICLE MODEL; OR (3) THE CONCESSIONS FOR THE MANUFACTURER ARE
NO LONGER MADE AVAILABLE TO THE CONTRACT VENDOR.

SHOULD ANY OF THESE EVENTS OCCUR, THE STATE RESERVES THE OPTIONS OF
(1) THE CONTRACT MAY BE CANCELLED AND AWARDED TO THE NEXT LOWEST
RESPONSIVE AND RESPONSIBLE BIDDER WHOSE BID MEETS THE REQUIREMENTS SET
FORTH IN THIS INVITATION TO BID OR (2) THE COMMODITY MAY BE
READVERTISED TO AWARD UPON CANCELLATION OF APPLICABLE CONTRACT.

VENDOR REPORTING

CONTRACT VENDORS WILL BE REQUIRED TO SUBMIT REPORTS VALIDATING
CONTRACT PURCHASES, INCLUDING PURCHASES MADE BY LOCAL GOVERNMENTS, BY
PERIOD, LINE ITEM AND RECEIVING LOCATION. REPORTS WILL DETAIL A
MINIMUM THE FOLLOWING INFORMATION:

1. CONTRACT NUMBER
2. CONTRACT LINE ITEM NUMBERT
3. COMMODITY DESCRIPTION
4. LINE ITEM QUANTITY PURCHASED
5. LINE ITEM DOLLAR AMOUNT (VOLUME) PURCHASED

ADDITIONAL REPORT DETAILS MAY BE REQUIRED WITH A THIRTY (30) DAY
WRITTEN NOTICE. REPORTS ARE DUE AT THE PURCHASING DIVISION OFFICE IN
THE FIRST WEEK OF THE FOURTH (4TH) QUARTER OF THE CONTRACT TERM.
REPORTS MUST BE SUBMITTED ELECTRONICALLY OR BY DIGITAL APPLIANCE IN
MICROSOFT EXCEL FORMAT. SEMI-ANNUAL OR QUARTERLY REPORTS MAY BE
REQUESTED IN WRITING BY THE CONTRACT ADMINISTRATOR WITH A THIRTY (30)
DAY WRITTEN NOTICE TO THE VENDOR.

PROHIBITION OF ILLEGAL IMMIGRANTS

THE REQUIREMENTS OF STATE OF TENNESSEE'S PUBLIC ACTS, 2006, CHAPTER
NUMBER 878 AND EXECUTIVE ORDER 41 ADDRESSING THE USE OF ILLEGAL
IMMIGRANTS IN THE PERFORMANCE OF ANY CONTRACT TO SUPPLY GOODS OR
SERVICES TO THE STATE OF TENNESSEE, SHALL BE A MATERIAL PROVISION OF
THIS CONTRACT, A BREACH OF WHICH SHALL BE GROUNDS FOR MONETARY AND
OTHER PENALTIES, UP TO AND INCLUDING TERMINATION OF THIS CONTRACT.


AS REQUIRED BY PUBLIC ACTS, 2006, CHAPTER NUMBER 878, NO PERSON MAY
ENTER INTO A CONTRACT TO SUPPLY GOODS OR SERVICES TO THE STATE WITH-
OUT FIRST ATTESTING IN WRITING THAT THE PERSON WILL NOT KNOWINGLY
UTILIZE THE SERVICES OF ILLEGAL IMMIGRANTS IN THE PERFORMANCE OF THIS
CONTRACT, AND WILL NOT KNOWINGLY UTILIZE THE SERVICES OF ANY
SUBCONTRACTOR WHO WILL UTILIZE THE SERVICES OF ILLEGAL IMMIGRANTS IN
THE PERFORMANCE OF THIS CONTRACT. FOR PURPOSES OF THIS CONTRACT,
"ILLEGAL IMMIGRANT" SHALL BE DEFINED AS ANY PERSON WHO IS NOT
EITHER A UNITED STATES CITIZEN, A LAWFUL PERMANENT RESIDENT, OR A
PERSON WHOSE PHYSICAL PRESENCE IN THE UNITED STATES IS
AUTHORIZED OR ALLOWED BY THE DEPARTMENT OF HOMELAND SECURITY AND WHO,
UNDER FEDERAL IMMIGRATION LAWS AND/OR REGULATIONS, IS AUTHORIZED TO
BE EMPLOYED IN THE U.S. OR IS OTHERWISE AUTHORIZED TO
PROVIDE SERVICES UNDER THE CONTRACT. THE CONTRACTOR HEREBY ATTESTS,
CERTIFIES, WARRANTS, AND ASSURES THAT IT SHALL COMPLY WITH THIS TERM
AND CONDITION FOR THE ENTIRE CONTRACT PERIOD.

THE CONTRACTOR UNDERSTANDS AND AGREES THAT FAILURE TO COMPLY WITH
THIS SECTION WILL BE SUBJECT TO THE SANCTIONS OF PUBLIC CHAPTER 878
OF 2006 FOR ACTS OR OMISSIONS OCCURRING AFTER ITS EFFECTIVE DATE. THIS
LAW REQUIRES THE COMMISSIONER OF FINANCE AND ADMINISTRATION TO
PROHIBIT A CONTRACTOR FROM CONTRACTING WITH, OR SUBMITTING AN OFFER,
PROPOSAL, OR BID TO CONTRACT WITH THE STATE OF TENNESSEE TO SUPPLY
GOODS OR SERVICES FOR A YEAR AFTER A CONTRACTOR IS DISCOVERED TO
HAVE KNOWINGLY USED THE SERVICES OF ILLEGAL IMMIGRANTS DURING THE
PERFORMANCE OF THIS CONTRACT. THE CONTRACTOR MAY APPEAL THE
IMPOSITION OF THE ONE-YEAR PROHIBITION BY UTILIZING AN APPEALS
PROCESS ESTABLISHED BY THE COMMISSIONER OF FINANCE AND ADMINISTRATION.

AS PER EXECUTIVE ORDER 41, THE CONTRACTOR SHALL BE REQUIRED TO SUBMIT
SEMI-ANNUAL ATTESTATION FORMS AND OBTAIN A SIGNED ATTESTATION FORM
FROM ANY SUBCONTRACTOR PRIOR TO THE USE OF THE SUBCONTRACTOR AND SEMI-
ANNUALLY THEREAFTER DURING THE CONTRACT PERIOD. THE RECORDS SHALL BE
SUBJECT TO REVIEW AND RANDOM INSPECTION AT ANY REASONABLE TIME UPON
REASONABLE NOTICE BY THE STATE. RECORDS SHALL INCLUDE BUT ARE NOT
LIMITED TO THE FOLLOWING:
1.) DOCUMENTATION ON CONTRACTORS' EMPLOYEES AND SUBCONTRACTOR
PERSONNEL WORKING ON THIS CONTRACT SHOWING THAT THEY ARE LEGAL
TO WORK IN THE UNITED STATES AND PAYROLL RECORDS.
2.) SIGNED AND DATED ATTESTATION FORMS FOR YOUR COMPANY THAT HAVE
BEEN SUBMITTED TO THE PURCHASING DIVISION AND ATTESTATION FORMS
OBTAINED FROM SUBCONTRACTOR(S).

NOTE: THE CONTRACTOR SHALL BE REQUIRED TO OBTAIN PRIOR APPROVAL TO
SUBCONTRACT FROM THE DEPUTY COMMISSIONER OF GENERAL SERVICES,
PURCHASING DIVISION.

BY AUTHORIZED SIGNATURE ON THIS INVITATION TO BID THE CONTRACTOR
CONSTITUTES SIGNING THE ATTESTATION FORM FOR THE INITIAL SIX (6)
MONTHS OF THE CONTRACT PERIOD. THE CONTRACTOR SHALL BE REQUIRED
TO SUBMIT SIGNED ATTESTATION FORMS ON A SEMI-ANNUAL BASIS FROM THE
START DATE OF THE CONTRACT PERIOD THROUGH TO ITS COMPLETION DATE TO
THE PURCHASING DIVISION. THE ATTESTATION FORM IS LOCATED ON THE
PURCHASING DIVISION WEBSITE: WWW.STATE.TN.US/GENERALSERV/PURCHASING
IN THE EVENT THAT THE CONTRACTOR FAILS TO SUBMIT THE ATTESTATION FORM,
FILLED OUT, DATED AND SIGNED, BY THE END OF ANY SIX MONTH CONTRACT
INTERVAL, THE CONTRACTOR SHALL BE NOTIFIED IN WRITING OF THE
REQUIREMENT TO SUBMIT THE ATTESTATION FORM WITHIN SEVEN (7) CALENDAR
DAYS; FAILURE TO SUBMIT THE ATTESTATION FORM WITHIN THE REQUIRED TIME
FRAME MAY RESULT IN THE CANCELLATION OF THE CONTRACT.
ORDER CUT OFF DATE/CONTRACT END DATE

THE SUCCESSFUL VENDOR MUST ADVISE THE PURCHASING DIVISION OF THE DATE
AFTER WHICH THE MANUFACTURER WILL NOT ACCEPT ORDERS FOR PRODUCTION.
INFORMATION MUST BE FORWARDED TO THE PURCHASING DIVISION IN WRITING
THE DAY AFTER THE INFORMATION IS RECEIVED BY THE SUCCESSFUL VENDOR.

THE PURCHASING DIVISION WILL INACTIVATE THE CONTRACT EFFECTIVE WITH
THE MANUFACTURER'S CUT-OFF DATE. NO ORDERS MAY BE PLACED WITH THE
VENDOR AFTER THIS DATE

IF THE AWARDED VENDOR DESIRES FOR THE CONTRACT TO REMAIN ACTIVE AFTER
THE MANUFACTURER'S CUT-OFF DATE, THE PURCHASING DIVISION MUST BE
NOTIFIED IN WRITING OF THIS REQUEST. THE REQUEST SHOULD INCLUDE THE
NUMBER OF VEHICLES AVAILABLE. THE VENDOR WILL THEN BE REQUIRED TO
HONOR ALL PURCHASE ORDERS RECEIVED UNTIL THE QUANTITY IS DEPLETED, ALL
TERMS AND CONDITIONS OF THE CONTRACT, AND ALL PRICING INCLUDING
APPLICABLE DISCOUNTS FOR PROMPT PAY. THE VENDOR WILL FURTHER BE
REQUIRED TO NOTIFY THE PURCHASING DIVISION IN WRITING OF THE DATE
WHEN THE DEALER'S STOCK ON HAND IS DEPLETED.

MAIL AND/OR FAX INFORMATION TO:

PURCHASING DIVISION
THIRD FLOOR, TENNESSEE TOWER
312 ROSA L. PARKS AVENUE
NASHVILLE, TN. 37243-0111
ATTN: BILL (SEWELL) DAVIS
FAX: (615) 741-0684
E-MAIL: SEWELL.DAVIS@STATE.TN.US

MOTOR VEHICLE MANAGEMENT
2200 CHARLOTTE AVENUE
NASHVILLE, TN. 37219
ATTN: TERRY LINDSEY
FAX: (615) 327-1559
E-MAIL: TERRY.LINDESY@STATE.TN.US
PRE-DELIVERY INSPECTION

THE CONTRACTOR, PRIOR TO DELIVERY, WILL PERFORM PRE-DELIVERY
INSPECTION (PDI). ANY VEHICLE FOUND NOT TO BE IN COMPLIANCE WITH THIS
REQUIREMENT MAY NOT BE ACCEPTED BY THE RECEIVEING AGENCY FOR THE
PURPOSE OF DELIVERY. THE PDI WILL INCLUDE BUT IS NOT LIMITED TO THE
MANUFACTURER'S RECOMMENDATIONS AS WELL AS THE FOLLOWING:

1. TIRES ARE TO BE INSPECTED TO INSURE PROPER INFLATION LEVELS.
2. ALL FLUID LEVELS TO BE CHECKED AND CORRECTED AS NEEDED.
3. ANTENNA IS TO BE IN THE OPERATING POSITION PRIOR TO DELIVERY.
4. FLOOR MATS ARE TO BE COLOR KEYED AND PLACED IN THE CORRECT FLOOR
AREA (NOT IN THE TRUNK). IF MATS ARE NOT THE CORRECT COLOR, VENDOR
SHALL NOT DELIVER THIS VEHICLE.
5. REMOVE ANY UNNECESSARY MANUFACTURER'S TAPE, STIKERS, DECALS,
LABELS OR OTHER ITEMS EXCEPT FOR THE ITEMIZED WINDOW STICKER WITH
E.P.A. FUEL ECONOMY ESTIMATES.
6. VEHICLE IS TO BE TEST DRIVEN AND ALL FEATURES ARE TO BE CHECKED TO
INSURE PROPER OPERATION.
7. ANY FINAL ASSEMBLY OR INSTALLATION OF FEATURES, EQUIPMENT OR ANY
OPTIONS MUST BE COMPLETED PRIOR TO DELIVERY.
8. ALL NECESSARY REPAIRS AND/OR ADJUSTEMENTS MUST BE MADE PRIOR TO
DELIVERY.
ADDITIONAL TERMS & CONDITIONS

(A) DELIVERY - ALL DELIVERYS ARE TO BE MADE BETWEEN THE HOURS OF
8:00 A.M. AND 4:00 P.M. MONDAY THROUGH FRIDAY.

(B) ACCEPTANCE - DELIVERY DOES NOT MEAN ACCEPTANCE. ALL VEHICLES ARE
SUBJECT TO INSPECTION TO ESTABLISH CONFORMITY TO SPECIFICATIONS
PRIOR TO ACCEPTANCE.
PILOT INSPECTION

PRIOR TO INITIAL DELIVERY OF TENNESSEE HIGHWAY PATROL VEHICLES, THE
MANUFACTURER SHALL SCHEDULE A PILOT MODEL INSPECTION IN ORDER TO
DETERMINE COMPLIANCE WITH SPECIFICATIONS. THE STATE RESERVES THE
RIGHT TO CONDUCT INSPECTION AT EACH POINT OF VEHICLE ASSEMBLY. UPON
WRITTEN PROPOSAL FROM THE MANUFACTURER, THE DEPARTMENT OF SAFETY AND
MOTOR VEHICLE MANAGEMENT MAY JOINTLY APPROVE A PROPOSAL TO HOLD THE
PILOT INSPECTION AT A LOCATION OTHER THAN AT THE POINT(S) OF VEHICLE
ASSEMBLY. THE WRITTEN PROPOSAL SHALL ARTICULATE JUST CAUSE AND/OR
EXTENUATING CIRCUMSTANCES FOR THIS DEVIATION.

ADDITIONAL SPECIFICATIONS FOR ALL VEHICLES

THE SPECIFICATIONS LISTED ARE CONSIDERED BASE VEHICLES FOR THIS BID.
THE STANDARD BASE VEHICLE MAY INCLUDE ITEMS THAT ARE NOT INCLUDED
BY THE MANUFACTURER ON THIS STANDARD BASE VEHICLE. WHEN THESE ITEMS
ARE INCLUDED IN THE STATE SPECIFICATIONS, THE BIDDER MUST INCLUDE
THE COST FOR THESE ITEMS IN THE BID. INCLUDED FOR ALL VEHICLES
STATED:

1) VEHICLE TO BE COMPLETELY WINTERIZED

2) MINIMUM OF 1/4 TANK OF FUEL (BY FUEL GAUGE) UPON DELIVERY

3) SUCESSFUL BIDDER TO SUPPLY THREE (3) SETS OF KEYS PER UNIT

4) PRE-DELIVERY ACCORDING TO MANUFACTURER'S STANDARD REQUIREMENTS

5) INVOICE TO INCLUDE IGNITION AND TRUNK KEY NUMBERS.

6) NO DEALER DECALS/EMBLEMS ARE TO BE ATTACHED TO THE VEHICLE

7) VEHICLE TO BE CLEAN INSIDE AND OUT WITH ALL APPLICABLE STICKERS
REMOVED. PROTECTIVE COVERINGS AND PLASTIC TO BE REMOVED FROM
SEATS.

8) WARRANTY: 3 YEARS, 36,000 MILES BUMPER TO BUMPER WILL BEGIN ON
DATE VEHICLE IS PLACED IN SERVICE NOT TO EXCEED SIX (6) MONTHS
FROM DELIVERY DATE.

9) ALL VEHICLES ARE TO INCLUDE ALL EQUIPMENT ADVERTISED BY THE
MANUFACTURER AS STANDARD. FLEET DELETES WITH AGENCY APPROVAL
ONLY.
SPECIFICATIONS FOR POLICE PURSUIT SEDAN
120.0" WHEELBASE, 3.5 L, V-6 ENGINE, REAR WHEEL DRIVE
MODEL YEAR 2010

POLICE PURSUIT SEDANS OFFERED UNDER THIS SPECIFICATION SHALL BE
EQUIPPED WITH ALL EQUIPMENT ADVERTISED AS STANDARD EQUIPMENT FOR
POLICE PURSUIT VEHICLES AND SHALL MEET OR EXCEED THE FOLLOWING
DETAILED REQUIREMENTS. ALL VALUES SPECIFIED BELOW SHALL BE CONSIDERED
AS MINIMUMS, UNLESS OTHERWISE SPECIFIED.

SPECIFICATIONS:

1. AIR BAG - VEHICLE TO BE EQUIPPED WITH DRIVER AND PASSENGER
FRONT AIR BAGS

2. AIR CONDITIONING: FACTORY INSTALLED SYSTEM MUST BE DESIGNED TO
PREVENT COMPONENT DAMAGE DUE TO HIGH SPEED DRIVING.

3. ALTERNATOR SYSTEM: TRANSISTORIZED REGULATOR, 160 AMP MINIMUM
OUTPUT CAPICITY, MINIMUM CURB IDLE OUTPUT OF 45 AMPS (AT
MANUFACTURER'S RECOMMENDED IDLE SPEED). SHALL BE OF HEAVY
DUTY DESIGN, CAPABLE OF SURVIVING PATROL CAR OPERATION.
OUTPUT RATINGS ARE FOR TYPICAL UNDER HOOD AMBIENT TEMPERATURES
AND NOT S.A.E. RATING METHOD.

4. ANTIFREEZE: TO BE EQUIPPED WITH ANTIFREEZE PROTECTION TO -20
DEGREES F. MINIMUM.

5. BATTERY: 12 VOLT; LARGEST SIZE AVAILABLE, MAINTENANCE FREE,
78 AMP HOURS.

6. BODY SIDE MOLDING: VEHICLE WILL HAVE COMPLETE BODY SIDE MOLDINGS

7. BRAKES: POWER ASSISTED, FOUR (4) WHEEL DISC ANTI-LOCK BRAKING
SYSTEM.

8. POWER OUTLET: WIRED INDEPENDENT OF IGNITION SYSTEM.

9. COOLING SYSTEM: VEHICLE TO HAVE MAXIMUM SIZE COOLING SYSTEM
AVAILABLE; INCORPORATING "COOLANT RECOVERY" SYSTEM.

10. ENGINE: SIX (6) CYLINDER MANUFACTURED AND RECOMMENDED FOR
POLICE PACKAGE. ENGINE MUST BE EQUIPPED WITH AN INTERNAL OIL
COOLER. ENGINE MUST MEET THE LATEST PERFORMANCE STANDARDS FOR
ACCELERATION AND TOP SPEED AS ESTABLISHED FOR THE MICHIGAN
DEPARTMENT OF STATE POLICE AND MICHIGAN DEPARTMENT AND BUDGET.
MINIMUM ENGINE SIZE: 3.5L.

11. GAS TANK: MINIMUM NINETEEN (19) GALLON TANK.

12. GAUGES: TO BE EQUIPPED WITH MANUFACTURER'S POLICE PURSUIT
INDICATOR PACKAGE LOCATED IN THE INSTRUMENT PANEL.

13. GLASS: ALL WINDOWS SHALL BE HEAT ABSORBING TINTED TYPE.

14. HEADLIGHTS: TO BE EQUIPPED WITH HIGH AND LOW BEAM QUARTZ-HALOGEN
HEADLIGHTS.

15. HOOD LATCH RELEASE: TO BE EQUIPPED WITH INSIDE HOOD LATCH
RELEASE.

16. KEYS: FOUR (4) SETS OF KEYS TO BE FURNISHED WITH EACH CAR.
REMOTE ENTRY ON UNMARKED - 4 KEYS, 2 REMOTE.

17. LICENSE PLATE BRACKETS: VEHICLE SHALL BE EQUIPPED WITH MANUFACT-
URER SUPPLIED FRONT AND REAR LICENSE PLATE BRACKETS. (DEALER
MAY INSTALL.)

18. LIGHTS: A. MAP LIGHT IN ADDITION TO DOME LIGHT WITH SEPERATE
CONTROL; TO BE LOCATED BETWEEN VISORS. FACTORY INSTALLED
B. TRUNK COMPARTMENT: LIGHTS TO BE CONTROLLED BY
MERCURY OR EQUAL TYPE SWITCHES.

19. LOCKS: ALL LOCKS ON A CAR TO BE KEYED ALIKE. EACH UNIT SHALL
HAVE DIFFERENT KEY CODES.

20. MIRRORS-REAR VIEW: INSIDE: DAY/NIGHT TYPE.
OUTSIDE: POWER REMOTE CONTROL TYPE, INSTALLED
ON LEFT-HAND AND RIGHT-HAND DOORS. CONTROLS TO BE WITHIN REACH
OF DRIVER. RECTANGULAR DESIGN APPROXIMATE SIZE 5" X 3" MINIMUM
VIEWING AREA OF FIFTEEN (15) SQUARE INCHES.

21. POLICE RADIO NOISE AND ELECTRICAL SUPPRESSION PACKAGE: ALL
COMPUTER RADIO RECEIVING AND OTHER ELECTRONIC SYSTEMS SHALL NOT
EXCEED THE RADIO FREQUENCY EMISSION LEVEL ALLOWABLE FOR SUCH
DEVICES BY PART 15 OF THE FEDERAL COMMUNICATIONS COMMISSION
RULES. SUCH DEVICES SHALL IN NO CASE CAUSE MORE THAN 3DB
REDUCTION IN EFFECTIVE RECEIVER SENSITIVITY AS MEASURED ABOVE.
NEITHER NOISE NOR VOLTAGE POTENTIAL DIFFERENCE SHALL BE
GENERATED BY MOVEMENT OR LACK OF CONDUCTIVITY BETWEEN BODY
OR CHASSIS COMPONENT PARTS. THE ABOVE REQUIREMENT MAY BE MET
BY THE USE OF CONDUCTIVE BONDING DEVICES OR THROUGH INHERENT
PRODUCT DESIGN.

22. POWER DOOR LOCKS: POWER DOOR LOCKS TO BE CONTROLLED FROM DRIVER
SIDE.

23. POWER WINDOWS: POWER WINDOWS CONTROLLED FROM DRIVER SIDE.

24. RADIO: AM-FM ELECTRONIC STEREO, WITH DIGITAL CLOCK, FACTORY INS-
TALLED WITH STANDARD NOISE AND ELECTRICAL SUPPRESSION PACKAGE.`

25. REAR WINDOW DEFOGGER: ELECTRICAL GRID TYPE. CONTROL TO BE
WITHIN CONVENIENT REACH OF DRIVER, CONTROL SWITCH TO BE CLEARLY
MARKED AS A FUNCTION.

26. SPEEDOMETER: SHALL BE CALIBRATED TO WITHIN +/-3 M.P.H ACCURACY.
SCALE GRADUATIONS TO BE LINEAR AND OF 2 M.P.H. INCREMENTS. 0 T0
160 M.P.H. SCALE MINIMUM. CALIBRATED DIGITAL IS ACCEPTABLE.

27. SEATS-ASSEMBLY, FRONT: BUCKET SEAT TYPE WITH RECLINER.
BOTH SEATS TO HAVE HEAVY DUTY INTERIOR CONSTRUCTION DESIGNED
FOR RUGGED POLICE USE, COMFORTABLE FOAM-PADDED SEAT CUSHIONS
AND BACKS.
REAR SEAT: BENCH

28. UPHOLSTERY: FRONT SEAT - HEAVY DUTY CLOTH.
REAR SEAT - HEAVY DUTY CLOTH FOR UNMARKED UNITS
HEAVY DUTY VINYL FOR MARKED UNITS
FLOORBOARD - CARPET ON ALL FLOORBOARDS, COLOR CO-
ORDINATED AND MATCHING FLOOR MATS FRONT AND REAR.
FACTORY INSTALLED

29. SUSPENSION: TO BE EQUIPPED WITH HEAVY DUTY SHOCK ABSORBERS FRONT
AND REAR, SPRINGS FRONT AND REAR, OR TORSION BARS ON FRONT WITH
SPRINGS ON REAR. SHOCKS ARE TO BE BEST QUALITY OFFERED FOR
HIGH SPEED PURSUIT DRIVING AND ROAD ABILITY. STABILIZER BARS
ARE REQUIRED ON FRONT AND REAR (POLICE PACKAGE TYPE).

30. AXLE RATIO: MINIMUN 2.82.

31. STEERING: POWER STEERING, DESIGNED FOR HIGH SPEED PURSUIT TYPE
DRIVING, WITH OIL COOLER.

32. STEERING WHEEL: TILT STEERING WHEEL WITH ANTI-SLIP SURFACE.

33. TIRES: TIRES (INCLUDING SPARE) TO BE MANUFACTURERS STANDARD
RADIALS, OR EQUAL WHICH MET THE STATE OF MICHIGAN SPECIFICATION
5260-S1. SPEED RATING TO MEET OR EXCEED VEHICLE PERFORMANCE
CAPABILITIES. SHALL BE V RATED AT 147 MPH MINIMUM RATING FOR
TIRE. SPARE SHALL BE FULL SIZE.

34. TOOLS: WHEEL WRENCH AND HEAVY DUTY JACK.

35. TRANSMISSION: FOUR (4) SPEED AUTOMATIC OVERDRIVE WHICH WILL
PREVENT THE ENGINE FROM OVER - REVING. BRAKE/TRANSMISSION
SHIFT, INTERLOCK. TRANSMISSION WILL BE EQUIPPED WITH MANUFACT-
URER'S RECOMMENDED AUXILIARY TRANSMISSION OIL COOLER, SUITABLE
FOR POLICE PURSUIT VEHICLES CONFORMING TO THESE SPECIFICATIONS.

36. TRUNK: TRUNK TO HAVE FULL LUGGAGE COMPARTMENT TRIM. VINYL MAT
IS NOT ACCEPTABLE.

37. TRUNK RELEASE, REMOTE: TO BE EQUIPPED WITH ELECTRONICALLY
OPERATED REMOTE CONTROL TRUNK RELEASE. CONTROL TO BE WITHIN
CONVENIENT REACH OF THE DRIVER. IN THE GLOVE BOX IS NOT
ACCEPTABLE.

38. WARRANTY: MANUFACTURER'S STANDARD WARRANTY FOR THIRTY-SIX (36)
MONTHS OR 36,000 MILES, WHICHEVER COMES FIRST. WARRANTY MUST
COINCIDE WITH IN SERVICE DATE, NOT DELIVERY DATE. IN SERVICE
DATE NOT TO EXCEED NINE (9) MONTHS FROM DELIVERY DATE.

39. WHEELBASE: MINIMUM 120.0

40. CRUISE CONTROL - REQUIRED

41. WHEELS: EIGHTEEN (18) INCH, HEAVY DUTY CONSTRUCTION (INCLUDING
SPARE) DESIGNED FOR POLICE USE, BLACK IN COLOR.

42. WHEEL COVERS: CROME, CENTER CAP (MARKED), FULL COVER (UNMARKED)

43. WINDSHIELD WASHERS: ELECTRIC, MANUFACTURER'S PERFORMANCE
STANDARDS.

44. WINDSHIELD WIPERS: MULTIPLE SPEED ELECTRIC, WITH INTERVAL.

45. UNMARKED UNITS TO INCLUDE STREET APPEARANCE PACKAGE

46. POLICE PACKAGE AND WIRING ACCESSORY UNIT TO CONTAIN POLICE PREP
PACKAGE BASE - INCLUDE THE ITEMS LISTED:

BASE POLICE PREP PACKAGE
TWO (2) FRONT STROBE BULBS AND FOUR (4) REAR STROBES, INSTALLED IN
MARKER LIGHTS, REAR TAILLIGHTS, AND BACKUP LIGHTS.
ALTERNATING HEADLIGHT FLASHER OVERRIDE WIRE AND RELAY
TRUNK PIGTAIL HARNESS WITH HEAVY-GAUGE POWER AND SIREN/SPEAKER
WIRED FOR INTALLER USE.
WIRING HARNESS INCLUDNG THE FOLLOWING ITEMS:
- SIX (6) STROBE CABLES - SHIELDED AND GROUNDED PRE-RUN TO THE
FRONT MARKER LIGHTS, TAILLIGHTS LENSES AND TWO (2) TO THE FRONT
LIGHTS, TWO (2) TO THE REAR TAILLIGHTS, AND TWO (2) TO THE
BACKUP LIGHTS.
- DISTRIBUTION CENTERS LOCATED IN THE GLOVE BOX AND TRUNK 50 AMP.
EACH DISTRIBUTION CENTER HAS FIVE (5) POWER AND GROUND WIRES AND
CAN HOLD SIX (6) FUSES - THREE (3) BATTERY AND THREE (3)
IGNITION POWERED. PLACED IN TRUNK TO BE LOCATED ON RIGHT SIDE.
- 50 AMP BATTERY CIRCUIT AND GROUND AVAILABLE AT CONSOLE BASE OR
TRUNK
- ADDITIONAL 50 AMP BATTERY CIRCUIT AND GROUND AVAILABLE AT TRUNK.
- 50 AMP BATTERY CIRCUIT AND GROUND AVAILABLE AT PASSENGER KICK
PANEL OR TRUNK, FOR RADIO COMMUNICATIONS.
- SIREN/SPEAKER WIRING PRE-RUN TO FRONT OF VEHILCLE AVAILABLE AT
CONSOLE BASE OR TRUNK (4 WIRES).
- HORN/SIREN RELAY CIRCUIT AVAILABLE AT CONSOLE BASE OR TRUNK
- FOUR (4) EXTRA CIRCUITS PRE-RUN FROM THE ENGINE COMPARTMENT TO
CONSOLE BASE.
- FOUR (4) EXTRA CIRCUITS PRE-RUN FROM THE CONSOLE BASE TO TRUNK.
ALTERNATING HEADLIGHT FLASHER. LIGHTED TOGGLE SWITCH INCLUDED.
ADDITIONAL CONTROL MODULE FOR CONNECTION TO CUSTOMER SUPPLIED
POSITIVE CONTROL SWITCH BOX.

47. IN ADDITION TO BASE POLICE PACKAGE, UNIT SHALL ALSO INCLUDE:
-CONSOLE MOUNTING PLATFORM, SECURED USING EXISTING MOUNTING POINTS
THE POWDER-COATED ALUMINUM MOUNTING PLATE IS PRE-DRILLED FOR
THE ADDITION OF EQUIPMENT (WITHOUT ARMREST) NO CENTER WIRING
CONDUIT TO BE INCLUDED. CONSOLE TO STOP AT BACK OF FRONT SEAT
AS NOT TO INTERFERE WITH CAGE INSTALLATION.
-STROBE POWER SUPPPLY, SIX (6) OUTLETS WITH FRONT SHUTDOWN.
STROBE POWER SUPPLY TO BE SUPPLIED, MAY NOT BE INSTALLED IN
VEHICLE. THE STATE OF TENNESSEE MAY BE RESPONSIBLE FOR
INSTALLATION.
-TWO HIGH INTENSITY FLASHING REAR DECK LED LIGHTS, WITH
MATCHING INTERIOR COLOR HOUSINGS. BLUE-BLUE
-TWO LED GRILL LIGHTS, WHELEN D2BB (P/N: 01-0684607-01) OR EQUAL
COLOR OF LED GRILL LIGHTS TO BE BLUE.
-TRUNK AIR CIRCULATION FAN, PULLS AIR FROM PASSEGER AREA AND
EXHAUSTS THROUGH TRUNK, STABILIZING CLIMATE FOR EQUIPMENT
AND HELPS CONTROL MOISTURE AND HUMIDITY.

NOTE: ALL ITEMS SHALL BE FACTORY INSTALLED UNLESS OTHERWISE NOTED.

ONLY ACCEPTABLE BRAND/MODEL: DODGE CHARGER
@
SPECIFICATIONS FOR POLICE PURSUIT SEDAN
110.5" WHEELBASE, 3.9 L V-6 ENGINE, FRONT WHEEL DRIVE
MODEL YEAR 2010

POLICE PURSUIT SEDANS OFFERED UNDER THIS SPECIFICATION SHALL BE
EQUIPPED WITH ALL EQUIPMENT ADVERTISED AS STANDARD EQUIPMENT
FOR POLICE PURSUIT VEHICLES AND SHALL MEET OR EXCEED THE FOLLOWING
DETAILED REQUIREMENTS. ALL VALUES SPECIFIED BELOW SHALL BE CONSIDERED
AS MINIMUMS, UNLESS OTHERWISE SPECIFIED.

SPECIFICICATIONS:

1. AIR BAG - VEHICLE TO BE EQUIPPED WITH DRIVER AND PASSENGER FRONT
AIR BAG.

2. AIR CONDITIONING: FACTORY INSTALLED SYSTEM MUST BE DESIGNED TO
PREVENT COMPONENT DAMAGE DUE TO HIGH SPEED DRIVING.

3. ALTERNATOR SYSTEM: TRANSISTORIZED REGULATOR, 150 AMP MINIMUM
OUTPUT CAPACITY, MINIMUM CURB IDLE OUTPUT OF 125 AMPS (AT
MANUFACTURER'S RECOMMENDED IDLE SPEED) AND 150 AMPS AT 1200 RPM
IDLE BOOST. SHALL BE OF A HEAVY DUTY DESIGN, CAPABLE OF
SURVIVING PATROL CAR OPERATION. OUTPUT RATINGS ARE FOR TYPICAL
UNDER HOOD AMBIENT TEMPERTURES AND NOT S.A.E. RATING METHOD.

4. ANTIFREEZE: TO BE EQUIPPED WITH ANTIFREEZE PROTECTION TO -30
DEGREES F. MINIMUM.

5. BATTERY: 12 VOLT; MINIMUM 720 COLD CRANKING AMPS.

6. BODY SIDE MOLDING: VEHICLE TO HAVE BODY SIDE MOLDINGS.

7. BRAKES: POWER ASSISTED, LOW PEDAL POSITION. FOUR (4) WHEEL
DISC BRAKES. ANTI-LOCK SYSTEM IS REQUIRED.

8. COOLING SYSTEM: VEHICLE TO HAVE MAXIMUM SIZE COOLING SYSTEM
AVAILABLE; INCORPORATING "COOLANT RECOVERY" SYSTEM FACTORY
INSTALLED.

9. ENGINE: LARGEST AVAILABLE SIX (6) CYLINDER, MANUFACTURED AND
RECOMMENDED FOR POLICE PACKAGE.

10. GAS TANK: MINIMUM 17.0 GALLONS

11. GAUGES: TO BE EQUIPPED WITH MANUFACTURER'S POLICE PURSUIT GUAGE
INDICATOR PACKAGE LOCATED IN THE INSTRUMENT PANEL.

12. GLASS: ALL WINDOWS SHALL BE HEAT ABSORBING (TINTED) TYPE.

13. HEADLIGHTS: TO BE EQUIPPED WITH HIGH AND LOW BEAM
COMPOSITE HALOGEN HEADLIGHTS.

14. HOOD LATCH RELEASE: TO BE EQUIPPED WITH INSIDE HOOD LATCH
RELEASE.

15. KEYS: FOUR (4) SETS OF KEYS TO BE FURNISHED WITH EACH CAR.
REMOTE ENTRY ON UNMARKED - 4 KEYS, 2 REMOTE.

16. LICENSE PLATE PROVISION: VEHICLE SHALL BE EQUIPPED WITH MANU-
FACTURER SUPPLIED FRONT AND REAR LICENSE PLATE PROVISIONS.
(DEALER MAY INSTALL)

17. LIGHTS: A. NIGHT SAVER LIGHT IN ADDITION TO DOME LIGHT WITH
SEPARATE CONTROL; TO BE LOCATED BETWEEN VISORS.
(MAYBE DEALER INSTALLED)
B. TRUNK COMPARTMENT: LIGHTS TO BE CONTROLLED BY
MERCURY OR EQUAL TYPE SWITCHES.

18. LOCKS: ALL LOCKS ON A CAR TO BE KEYED ALIKE. EACH UNIT SHALL
HAVE DIFFERENT KEY CODES.

19. INSIDE MIRRORS: REAR VIEW: DAY/NIGHT

20. OUTSIDE MIRRORS: REAR VIEW REMOTE CONTROL TYPE, INSTALLED ON
LEFT-HAND AND RIGHT-HAND DOORS. CONTROLS TO BE WITHIN CONVENIENT
REACH OF THE DRIVER

21. POLICE RADIO NOISE AND ELECTRICAL SUPPRESSION PACKAGE: ALL
COMPUTER RADIO RECEIVING AND OTHER ELECTRONIC SYSTEMS SHALL
NOT EXCEED THE RADIO FREQUENCY EMISSION LEVEL ALLOWABLE FOR
SUCH DEVICES BY PART 15 OF THE FEDERAL COMMUNICATIONS COM-
MISSION RULES. SUCH DEVICES SHALL IN NO CASE CAUSE MORE THAN
3DB REDUCTION IN EFFECTIVE RECEIVER SENSITIVITY AS MEASURED
AT THE POLICE MOBILE RADIO ANTENNA JACK WHEN SUCH RADIO IS
INSTALLED IN THE VEHICLE. NOISE SHALL NOT BE INTRODUCED INTO
ELECTRICAL WIRING SYSTEM WHICH WILL CAUSE MORE THAN 3DB RED-
UCTION IN EFFECTIVE RECEIVER SENSITIVITY AS MEASURED ABOVE.
IN NO CASE SHALL THE TOTAL EFFECTIVE SENSITIVITY REDUCTION
CAUSED BY ALL SOURCES BE GREATER THAN 3DB. NEITHER NOISE OR
VOLTAGE POTENTIAL DIFFERENCE SHALL BE GENERATED BY MOVEMENT OR
LACK OF CONDUCTIVITY BETWEEN BODY AND CHASSIS COMPONENT PARTS.
THE ABOVE REQUIREMENT MAY BE MET BY THE USE OF CONDUCTIVE BONDING
DEVICES OR THROUGH INHERENT DESIGN.

22. POWER DOOR LOCKS: POWER DOOR LOCKS TO BE CONTROLLED FROM DRIVER
SIDE.

23. POWER WINDOWS: POWER WINDOWS CONTROLLED FROM DRIVER SIDE.

24. RADIO: AM/FM ELECTRONIC STEREO WITH DIGITAL CLOCK, WITH
STANDARD NOISE AND ELECTRICAL SUPPRESSION PACKAGE

25. REAR WINDOW DEFOGGER: ELECTRICAL GRID TYPE. CONTROL TO BE
WITHIN CONVENIENT REACH OF DRIVER.

26. SPEEDOMETER: SHALL BE CALIBRATED TO WITHIN +/-3 M.P.H.
ACCURACY. SCALE GRADUATIONS TO BE LINEAR AND OF 2 M.P.H.
INCREMENTS. 0 - 140 M.P.H. SCALE MINIMUM. CALIBRATED DIGITAL
IS ACCEPTABLE.

27. FRONT SEAT ASSEMBLY: BUCKET SEAT TYPE, INDIVIDUALLY ADJUSTABLE.
BOTH SEATS TO HAVE HEAVY DUTY INTERIOR CONSTRUCTION DESIGNED
FOR RUGGED POLICE USE. FOAM PADDED SEAT CUSHIONS AND BACKS.
TO PERMIT THE INSTALLATION OF RADIO EQUIPMENT, FLOOR MOUNTED
SHIFT LEVER WITH CONSOLE IS NOT PERMITTED.

28. UPHOLSTERY: FRONT SEAT - HEAVY DUTY CLOTH
REAR SEAT - HEAVY DUTY CLOTH - UNMARKED UNITS
HEAVY DUTY VINYL - MARKED UNITS
FLOORBOARD - CARPET ON ALL FLOORBOARDS, COLOR
COORDINATED AND MATCHING FLOOR MATS
FRONT AND REAR.

29. SUSPENSION: TO BE EQUIPPED WITH HEAVY DUTY SHOCK ABSORBERS
FRONT AND REAR, SPRINGS FRONT AND REAR. SHOCKS ARE TO BE BEST
QUALITY OFFERED FOR HIGH SPEED PURSUIT DRIVING AND ROAD ABILITY.
STABILIZER BARS ARE REQUIRED ON FRONT AND REAR (POLICE
PACKAGE TYPE).

30. STEERING: POWER STEERING, DESIGNED FOR HIGH SPEED PURSUIT TYPE
DRIVING.

31. STEERING WHEEL: TILT STEERING WHEEL WITH ANTI-SLIP SURFACE.

32. TIRES: TIRES TO BE MANUFACTURERS STANDARD PURSUIT TIRES WITH
SPEED RATINGS TO MEET OR EXCEED VEHICLE PERFORMANCE CAPABILITIES.
FULL SIZE

33. TOOLS: WHEEL WRENCH AND HEAVY DUTY JACK.

34. TRANSMISSION: FOUR (4) SPEED AUTOMATIC OVERDRIVE WHICH WILL
PREVENT THE ENGINE FROM OVER REVING.

35. TRUNK RELEASE, REMOTE: TO BE EQUIPPED WITH ELECTRONICALLY
OPERATED REMOTE CONTROL TRUNK RELEASE. CONTROL TO BE WITHIN
CONVENIENT REACH OF THE DRIVER, (IN GLOVE BOX IS NOT ACCEPTABLE)
TRUNK REMOTE TO OPERATE ONLY WHEN THE IGNITION KEY IS IN "ON"
POSITION.

36. WARRANTY: MANUFACTURER'S STANDARD WARRANTY FOR THIRTY-SIX (36)
MONTHS OR 36,000 MILES, WHICHEVER COMES FIRST. WARRANTY MUST
COINCIDE WITH IN SERVICE DATE, NOT DELIVERY DATE. IN SERVICE
DATE NOT TO EXCEED NINE (9) MONTHS FROM DELIVERY DATE.

37. WHEELBASE: 110.5"

38. WHEELS: HEAVY DUTY CONSTRUCTION DESIGNED FOR POLICE USE.

39. WHEEL COVERS: K-DISK, FULL WHEEL COVERS (UNMARKED), CENTER CAP
(MARKED), MAY BE DEALER INSTALLED.

40. WINDSHIELD WASHERS: ELECTRIC, MANUFACTURER'S PERFORMANCE
STANDARDS.

41. WINDSHIELD WIPERS: MULTIPLE SPEED ELECTRIC, WITH INTERVAL.

42. CRUISE CONTROL: REQUIRED

43. NO ON-STAR OR XM RADIO.

44. UNMARKED UNITS TO INCLUDE STREET APPEARANCE PACKAGE

45. WIRING ACCESSORY: MANUFACTURER'S STANDARD WIRING FEATURES THAT
COMPLY TO THE ELECTRICAL REQUIREMENTS OF THESE SPECIFICATIONS
WILL BE ACCEPTED.

46. LIGHTING PACKAGE:
- CORNER STROBE, FRONT AND REAR CLEAR CORNER STROBES INSTALLED IN
FRONT HEAD LAMPS AND REAR TAIL LAMPS OF VEHICLE TO INCLUDE
POWER SUPPLY AND ALL STROBE CABLES ROUTED TO THE CARGO AREA
AND LEFT BLUNT CUT. STROBE POWER SUPPLY TO BE SUPPLIED BUT
NOT INSTALLED IN VEHICLE. THE STATE OF TENNESSEE WILL BE
RESPONSIBLE FOR INSTALLATION.
- TWO LOW PROFILE REAR LED DECK LAMPS, MOUNTED BEHIND THE REAR
SEAT BACK, THESE LOW PROFILE LED LAMPS PROVIDE A HIGH
INTENSITY LIGHT TO THE REAR WHETHER THE TRUNK LID IS UP OR
DOWN. FLASHER IS INTEGRAL WITH THE LAMP ASSEMBLY. REQUIRE
WIRE CONNECTION TO OPERATE. LOW PROFILE LAMP IS BLUE/BLUE.
- TWO LED GRILL LAMPS, FRONT FACING LED GRILL LIGHTS WHALEN D2BB
(P/N 01-0684607-01). COLOR OF LED GRILL LIGHTS TO BE BLUE
LOCATED BEHIND GRILL. REQUIRES WIRE CONNECTION TO OPERATE.

NOTE: ALL ITEMS SHALL BE FACTORY INSTALLED UNLESS OTHERWISE NOTED

ONLY ACCEPTABLE BRAND/MODEL: CHEVROLET IMPALA FLEX FUEL
@
SPECIFICATIONS FOR POLICE PURSUIT SEDAN
114.6" WHEELBASE, 4.6 L ENGINE, REAR WHEEL DRIVE
MODEL YEAR 2010

POLICE PURSUIT SEDANS OFFERED UNDER THIS SPECIFICATION SHALL BE
EQUIPPED WITH ALL EQUIPMENT ADVERTISED AS STANDARD EQUIPMENT FOR
POLICE PURSUIT VEHICLES AND SHALL MEET OR EXCEED THE FOLLOWING
DETAILED REQUIREMENTS. ALL VALUES SPECIFIED BELOW SHALL BE CONSIDERED
AS MINIMUMS, UNLESS OTHERWISE SPECIFIED.

SPECIFICATIONS:

1. AIR BAG - VEHICLE TO BE EQUIPPED WITH DRIVER AND PASSENGER FRONT
AIR BAGS.

2. AIR CONDITIONING: FACTORY INSTALLED SYSTEM MUST BE DESIGNED TO
PREVENT COMPONENT DAMAGE DUE TO HIGH SPEED DRIVING, WITH THREE (3
YEAR, 36,000 MILE WARRANTY FROM DATE VEHICLE IS PLACED INTO
SERVICE.

3. ALTERNATOR SYSTEM: TRANSISTORIZED REGULATOR, 130 AMP MINIMUM
OUTPUT CAPACITY, MINIMUM CURB IDLE OUTPUT OF 45 AMPS ( AT
MANUFACTURER'S RECOMMENDED IDLE SPEED). SHALL BE OF HEAVY
DUTY DESIGN, CAPABLE OF SURVIVING PATROL CAR OPERATION.
OUTPUT RATINGS ARE FOR TYPICAL UNDER HOOD AMBIENT TEMPERATURES
AND NOT S.A.E. RATING METHOD.

4. ANTIFREEZE: TO BE EQUIPPED WITH ANTIFREEZE PROTECTION TO -20
DEGREES F. MINIMUM.

5. BATTERY: 12 VOLT; LARGEST SIZE AVAILABLE, MAINTENANCE FREE,
78 AMP HOURS.

6. BODY SIDE MOLDING: VEHICLE WILL HAVE COMPLETE BODY SIDE MOLDINGS
FACTORY INSTALLED

7. BRAKES: POWER ASSISTED, FOUR (4) WHEEL DISC ANTI-LOCK BRAKING
SYSTEM.

8. POWER OUTLET: TO BE LOCATED ON INSTRUMENT PANEL. WIRED
INDEPENDENT OF IGNITION SYSTEM.

9. COOLING SYSTEM: VEHICLE TO HAVE MAXIMUM SIZE COOLING SYSTEM
AVAILABLE; INCORPORATING "COOLANT RECOVERY" SYSTEM FACTORY
INSTALLED.

10. ENGINE: EIGHT (8) CYLINDER MANUFACTURED AND RECOMMENDED FOR
POLICE PACKAGE. MUST BE THE LARGEST CUBIC INCH/LITER DISPLACE-
MENT AVAILABLE IN THE MODEL OF THE VEHICLE SUBMITTED. ENGINE
MUST BE EQUIPPED WITH AN INTERNAL OIL COOLER. ENGINE MUST MEET
THE LATEST PERFORMANCE STANDARDS FOR ACCELERATION AND TOP SPEED
AS ESTABLISHED FOR THE MICHIGAN DEPARTMENT OF STATE POLICE AND
MICHIGAN DEPARTMENT OF MANAGEMENT AND BUDGET. ACCEPTABLE
ENGINE SIZE: FORD CROWN VICTORIA 4.6L
(4.6L OVERHEAD CAM SEFI V8 WITH 250 HP AND 297 LB.-FT OF TORQUE)

11. GAS TANK: MINIMUM NINETEEN (19) GALLON TANK.

12. GAUGES: TO BE EQUIPPED WITH MANUFACTURER'S POLICE PURSUIT GUAGE
INDICATOR PACKAGE LOCATED IN THE INSTRUMENT PANEL.

13. GLASS: ALL WINDOWS SHALL BE HEAT ABSORBING TINTED TYPE.

14. HEADLIGHTS: TO BE EQUIPPED WITH HIGH AND LOW BEAM QUARTZ-HALOGEN
HEADLIGHTS.

15. HOOD LATCH RELEASE: TO BE EQUIPPED WITH INSIDE HOOD LATCH
RELEASE.

16. KEYS: FOUR (4) SETS OF KEYS TO BE FURNISHED WITH EACH CAR.
REMOTE ENTRY ON UNMARKED - 4 KEYS, 2 REMOTE.

17. LICENSE PLATE BRACKETS: VEHICLE SHALL BE EQUIPPED WITH MANUFACT-
URER SUPPLIED FRONT AND REAR LICENSE PLATE BRACKETS. (DEALER
MAY INSTALL.)

18. LIGHTS: A. MAP LIGHT IN ADDITION TO DOME LIGHT WITH SEPERATE
CONTROL; TO BE LOCATED BETWEEN VISORS. FACTORY INSTALLED.
B. TRUNK COMPARTMENT: LIGHTS TO BE CONTROLLED BY
MERCURY OR EQUAL TYPE SWITCHES.

19. LOCKS: ALL LOCKS ON A CAR TO BE KEYED ALIKE. EACH UNIT SHALL
HAVE DIFFERENT KEY CODES.

20. MIRRORS-REAR VIEW: INSIDE: DAY/NIGHT TYPE.
OUTSIDE: POWER REMOTE CONTROL TYPE, INSTALLED
ON LEFT-HAND AND RIGHT-HAND DOORS. CONTROLS TO BE WITHIN REACH
OF DRIVER. RECTANGULAR DESIGN APPROXIMATE SIZE 5" X 3" MINIMUM
VIEWING AREA OF FIFTEEN (15) SQUARE INCHES.

21. POLICE RADIO NOISE AND ELECTRICAL SUPPRESSION PACKAGE: ALL
COMPUTER RADIO RECEIVING AND OTHER ELECTRONIC SYSTEMS SHALL NOT
EXCEED THE RADIO FREQUENCY EMISSION LEVEL ALLOWABLE FOR SUCH
DEVICES BY PART 15 OF THE FEDERAL COMMUNICATIONS COMMISSION
RULES. SUCH DEVICES SHALL IN NO CASE CAUSE MORE THAN 3DB
REDUCTION IN EFFECTIVE RECEIVER SENSITIVITY AS MEASURED ABOVE.
NEITHER NOISE NOR VOLTAGE POTENTIAL DIFFERENCE SHALL BE
GENERATED BY MOVEMENT OR LACK OF CONDUCTIVITY BETWEEN BODY
OR CHASSIS COMPONENT PARTS. THE ABOVE REQUIREMENT MAY BE MET
BY THE USE OF CONDUCTIVE BONDING DEVICES OR THROUGH INHERENT
PRODUCT DESIGN.

22. POWER DOOR LOCKS: POWER DOOR LOCKS TO BE CONTROLLED FROM DRIVER
SIDE. FACTORY INSTALLED.

23. POWER WINDOWS: POWER WINDOWS CONTROLLED FROM DRIVER SIDE.
FACTORY INSTALLED.

24. RADIO: AM-FM ELECTRONIC STEREO, WITH DIGITAL CLOCK, FACTORY INS-
TALLED WITH STANDARD NOISE AND ELECTRICAL SUPPRESSION PACKAGE.`

25. REAR WINDOW DEFOGGER: ELECTRICAL GRID TYPE. CONTROL TO BE
WITHIN CONVENIENT REACH OF DRIVER, CONTROL SWITCH TO BE CLEARLY
MARKED AS A FUNCTION. FACTORY INSTALLED.

26. SPEEDOMETER: SHALL BE CALIBRATED TO WITHIN +/-3 M.P.H ACCURACY.
SCALE GRADUATIONS TO BE LINEAR AND OF 2 M.P.H. INCREMENTS. 0 T0
140 M.P.H. SCALE MINIMUM. CALIBRATED DIGITAL IS ACCEPTABLE.

27. SEATS-ASSEMBLY, FRONT: BUCKET SEAT TYPE WITH RECLINER.
BOTH SEATS TO HAVE HEAVY DUTY INTERIOR CONSTRUCTION DESIGNED
FOR RUGGED POLICE USE, COMFORTABLE FOAM-PADDED SEAT CUSHIONS
AND BACKS.
REAR SEAT: BENCH

28. UPHOLSTERY: FRONT SEAT - HEAVY DUTY CLOTH.
REAR SEAT - HEAVY DUTY CLOTH - UNMARKED UNITS
HEAVY DUTY VINYL - MARKED UNITS
FLOORBOARD - CARPET ON ALL FLOORBOARDS, COLOR CO-
ORDINATED AND MATCHING FLOOR MATS FRONT AND REAR.
FACTORY INSTALLED

29. SUSPENSION: TO BE EQUIPPED WITH HEAVY DUTY SHOCK ABSORBERS FRONT
AND REAR, SPRINGS FRONT AND REAR, OR TORSION BARS ON FRONT WITH
SPRINGS ON REAR. SHOCKS ARE TO BE BEST QUALITY OFFERED FOR
HIGH SPEED PURSUIT DRIVING AND ROAD ABILITY. STABILIZER BARS
ARE REQUIRED ON FRONT AND REAR (POLICE PACKAGE TYPE).

30. AXLE RATIO: MINIMUM 3.27

31. STEERING: POWER STEERING, DESIGNED FOR HIGH SPEED PURSUIT TYPE
DRIVING, WITH OIL COOLER.

32. STEERING WHEEL: TILT STEERING WHEEL WITH ANTI-SLIP SURFACE,
FACTORY INSTALLED.

33. TIRES: TIRES (INCLUDING SPARE) TO BE MANUFACTURERS STANDARD
PURSUIT TIRES WHICH MET THE STATE OF MICHIGAN SPECIFICATION
5260-S1. SPEED RATING TO MEET OR EXCEED VEHICLE PERFORMANCE
CAPABILITIES. SHALL BE V RATED AT 147 MPH MINIMUM RATING.
SPARE TO BE FULL SIZE.

34. TOOLS: WHEEL WRENCH AND HEAVY DUTY JACK.

35. TRANSMISSION: FOUR (4) SPEED AUTOMATIC OVERDRIVE WHICH WILL
PREVENT THE ENGINE FROM OVER - REVING. BRAKE/TRANSMISSION
SHIFT, INTERLOCK. TRANSMISSION WILL BE EQUIPPED WITH MANUFACT-
URER'S RECOMMENDED AUXILIARY TRANSMISSION OIL COOLER, SUITABLE
FOR POLICE PURSUIT VEHICLES CONFORMING TO THESE SPECIFICATIONS.

36. TRUNK: TRUNK TO HAVE FULL LUGGAGE COMPARTMENT TRIM. VINYL MAT
IS NOT ACCEPTABLE.

37. TRUNK RELEASE, REMOTE: TO BE EQUIPPED WITH ELECTRONICALLY
OPERATED REMOTE CONTROL TRUNK RELEASE. CONTROL TO BE WITHIN
CONVENIENT REACH OF THE DRIVER. IN THE GLOVE BOX IS NOT
ACCEPTABLE.

38. WARRANTY: MANUFACTURER'S STANDARD WARRANTY FOR THIRTY-SIX (36)
MONTHS OR 36,000 MILES, WHICHEVER COMES FIRST. WARRANTY MUST
COINCIDE WITH IN SERVICE DATE, NOT DELIVERY DATE. IN SERVICE
DATE NOT TO EXCEED NINE (9) MONTHS FROM DELIVERY DATE.

39. WHEELBASE: MINIMUM 114.6"

40. CRUISE CONTROL - REQUIRED

41. WHEELS: SEVENTEEN (17) INCH, HEAVY DUTY CONSTRUCTION (INCLUDING
SPARE) DESIGNED FOR POLICE USE, BLACK IN COLOR.

42. WHEEL COVERS: CROME, CENTER CAP (MARKED), FULL COVER (UNMARKED)

43. WINDSHIELD WASHERS: ELECTRIC, MANUFACTURER'S PERFORMANCE
STANDARDS.

44. WINDSHIELD WIPERS: MULTIPLE SPEED ELECTRIC, WITH INTERVAL.

45. UNMARKED UNITS TO INCLUDE STREET APPEARANCE PACKAGE

46. POLICE PACKAGE AND WIRING ACCESSORY" UNIT TO CONTAIN POLICE PREP
PACKAGE BASE - 65A TO INCLUDE BUT NOT LIMITED TO THE ITEMS LISTED:

BASE POLICE PREP PACKAGE (65A)
TWO (2) FRONT STROBE BULBS AND FOUR (4) REAR STROBES, INSTALLED IN
THE FRONT MARKER LIGHTS, REAR TAILLIGHTS `AND BACKUP LIGHTS.
WIRING HARNESS INCLUDNG THE FOLLOWING ITEMS:
- SIX (6) STROBE CABLES - SHIELDED AND GROUNDED PRE-RUN TO THE
FRONT MARKER LIGHTS, TAILLIGHTS LENSES AND TWO (2) TO THE FRONT
MARKER LIGHTS, TWO (2) TO THE REAR TAILLIGHTS, AND TWO (2) TO
THE BACKUP LIGHTS.
- DISTRIBUTION CENTERS LOCATED IN THE GLOVE BOX AND TRUNK 50 AMP,
EACH FUSED IN THE ENGINE COMPARTMENT. EACH DISTRIBUTION CENTER
HAS FIVE (5) POWER AND GROUND WIRES AND CAN HOLD SIX (6) FUSE -
THREE (3) BATTERY AND THREE (3) IGNITION POWERED. PLACED IN
TRUNK TO BE LOCATED ON RIGHT SIDE.
- 50 AMP BATTERY CIRCUIT AND GROUND AVAILABLE AT CONSOLE BASE OR
TRUNK
- ADDITIONAL 50 AMP BATTERY CIRCUIT AND GROUND AVAILABLE AT TRUNK.
- 50 AMP BATTERY CIRCUIT AND GROUND AVAILABLE AT PASSENGER KICK
PANEL OR TRUNK, FOR RADIO COMMUNICATIONS.
- SIREN/SPEAKER WIRING PRE-RUN TO FRONT OF VEHILCLE AVAILABLE AT
CONSOLE BASE OR TRUNK (4 WIRES).
- HORN/SIREN RELAY CIRCUIT AVAILABLE AT CONSOLE BASE OR TRUNK
- FOUR (4) EXTRA CIRCUITS PRE-RUN FROM THE ENGINE COMPARTMENT TO
CONSOLE BASE.
- FOUR (4) EXTRA CIRCUITS PRE-RUN FROM THE CONSOLE BASE TO TRUNK.
ALTERNATING HEADLIGHT FLASHER. ADDITIONAL CONTROL MODULE FOR
CONNECTION TO CUSTOMER SUPPLIED POSITIVE CONTROL SWITCH BOX.

47. IN ADDITION TO BASE POLICE PACKAGE 65A, UNIT SHALL ALSO INCLUDE:
-CONSOLE MOUNTING PLATFORM, SECURED USING EXISTING MOUNTING POINTS
THE POWDER-COATED ALUMINUM MOUNTING PLATE IS PRE-DRILLED FOR
THE ADDITION OF EQUIPMENT (WITHOUT ARMREST) NO CENTER WIRING
CONDUIT TO BE INCLUDED. CONSOLE TO STOP AT BACK OF FRONT SEAT
AS NOT TO INTERFERE WITH CAGE INSTALLATION.
-STROBE POWER SUPPLY, SIX (6) OUTLETS WITH FRONT SHUTDOWN.
STROBE POWER SUPPLY TO BE SUPPLIED BUT NOT INSTALLED IN
VEHICLE. THE STATE OF TENNESSEE WILL BE RESPONSIBLE FOR
INSTALLATION.
-TWO HIGH INTENSITY FLASHING REAR DECK LED LIGHTS, WITH
MATCHING INTERIOR COLOR HOUSINGS. BLUE-BLUE
-TWO LED BLUE LIGHTS INSTALLED IN THE GRILL AREA. WHELEN D2BB
(P/N: 01-0684607-01) OR EQUAL. GRILL LIGHTS TO BE BLUE.
-TRUNK AIR CIRCULATION FAN, PULLS AIR FROM PASSENGER AREA AND
EXHAUSTS THROUGH TRUNK, STABILIZING CLIMATE FOR EQUIPMENT
AND HELPS CONTROL MOISTURE AND HUMIDITY.

ONLY ACCEPTABLE BRAND/MODEL: FORD CROWN VICTORIA P7B FLEXFUEL